Sneek Peek Review
Welcome, and we begin with Chapter 1 – Inspections Sheet.
An inspection sheet is a living document. We use the phrase “living document” because it is an updated document every time there are changes to the tent permit application.
Inspection Sheet Checklist Definition
Chapter 1 : Functions of an Inspection Check List
Identifying life-safety tent and membrane structure code regulations before a disaster is an essential part of an inspection.
Click on the Arrow Head within the circle below and begin
the course Inspection Checklist.
The Advantages of an Inspection Check List
The advantages in creating “The Inspection Sheet” begins with:
- Reviewing the permit application
- It’s association with code requirements
- And restrictions.
A warning we are using the KISS logic “Keep it Simple Stupid.”
Functions of an Inspection Check List PDF Format
The next step is:
# Creating an Inspection Sheet.
# Begin with opening the permit application using the permit as reference
# The first step is to create a permit outline
# However, if you find the permit is not requesting or missing regulations
# may I suggest that you go back and fix the permit process
# and then create or modify your inspection sheet.
A reminder: the inspection sheet is a guideline for the AHJ or a third-party inspector who ends up with the responsibility to inspect the event, which allows us to follow our KISS formula.
The IFC regulation for “Construction Documents.” These documents usually are available thru the tent and membrane structure Manufacturers Installation Guidelines. The end of the report are photos illustrating the results, and the most important is the anchoring diagram. However, there are additional options, and these possibilities are exceptions.
So when do you grant exceptions? Each jurisdiction should create a policy as to when to initiate exceptions. Size can trigger this procedure, the number of attendees, and risk assessment. Once the administration establishes this system, the next step is forming your exception procedures and publishing the procedures for the AHJ and special event partners.
Construction and Manufacture's Installation Guidelines
We begin using the construction documents or installation diagrams as a guideline to match the code regulations to your inspection sheet. Once you are on site, start by following the inspection sheet guidelines. After you have finished with your inspection sheet, review the installation documents, which should be available at the job site, and decide if there are additional validation issues or regulations that you and the contact person should address. Once you are satisfied that the site has fulfilled its obligations, approve the inspection. If not, do not authorize an operational permit.
The Eraser Model for Really Big Mistakes
Before we move on there is a significant model you should incorporate into your inspection process….
The Eraser Model for Really, Realy Big Mistakes
I cannot take all of the credit for the eraser model because one of my advisory board members who is a Chicago Area Building Code Inspector, told me that it is much easier to use an eraser to fix a problem on paper than on the job site. His suggestion is to:
- Establish a policy of reviewing the construction documents, and determine that the construction documents are compliant with the regulations.
- However, if there is an error in the permit documents correcting the problem on paper is far more productive than discovering the infraction onsite.
- You may also have eliminated the possibility of a loud and animated discussion on the job site.
Therefore, we have established a simple process for developing an Inspection Sheet.
Onward to the physical location and construction documents…
Your packet of Construction Documents should include site plans.
The first inspection step begins with “Site Location.” The site location information is available from the construction documents or the permit application. However, I would strongly suggest that there are construction documents that you as an AHJ can follow versus information on the permit application. The same construction documents should also have the structural design information and floor plans.
We begin by arriving at the…
The first thing you should consider upon arriving at the location is whether the site location creates any safety concerns for those who will attend this event. A significant safety infraction at this point is a bit late in the permitting And you laughed at our Eraser Model!
The next step is the…
Documents, Drawings, and Certificates...
Will your permit request an approved design drawing from a registered design professional or was there a pre-approved exception granted for the tent or tents? Using the construction documents as a reference is the installation following the manufacturer’s guidelines? If not, ask the contact person “why.” Are there Flame Certificates available?
After you are satisfied with the structural design, we continue with your inspection course…
The Floor Plan...
The next step is the floor plan. Referencing the slide regulation numbers, you can validate egress, aisles, fire extinguishers, and occupant load. Once you are satisfied that the construction documents match the on-site configuration you have completed the floor plan.
I want to point out the egress chart and the design drawing. Notice that the table requests two exits, and the design drawing has one. Here is another example where a permit review would catch this infraction. My I boldly say, “the eraser model strikes again.”
We have completed Chapter 1 and on to the Chapter 2 – Pole Tents…